The content listed below pertaining to Tools You Need to Install a New Bathtub is without a doubt motivating. Don't bypass it.
Mounting a bath tub isn't precisely brain surgery, however it does call for strong plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bath tub with a new one is additionally a reasonably hard project. If the old tub is readily easily accessible, the job can move easily; if you have to open a wall to get rid of the old tub as well as place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will require a helper to move out the old tub as well as set in the new one. See to it you have actually certified on your own for the job as well as fit attempting it. Rather than working with a service provider to take over a halfway-completed project, it is far better to consider utilizing one before you start. Possibilities are you may require a professional plumber to make tube links.
This short article will assist you install a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water supply pipelines.
Your tools and also product checklist ought to comprise the following:
Planning for the Installment
To start with, the supporting frame supplied with the bath should be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to stop pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its last placement.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, switch on the faucets to drain any water continuing to be in the system. The process of removing the existing faucets can be quite problematic because of the restricted accessibility that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the staying water that will come from the pipelines. As soon as the supply pipelines have been eliminated, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before going on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Making use of both wooden boards under its feet, place the bath tub in the required placement. The wooden boards are helpful in equally spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the bathtub until the spirit level reads level.
To mount taps, fit the bottom of the furthest versatile faucet port to the proper supply pipeline by making a compression join; then do the very same for the other faucet.
Activate the water system as well as inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill up the tub as well as additionally examine the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub must wait up until the bathtub has been made use of a minimum of when as this will certainly resolve it into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in place in between the faucet as well as the sink. Safeguard the tap in position with the maker offered backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet connectors. The former type needs to be linked to the tap ends first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture a rigid seal, causing the water to permeate the wall between the bathroom and also the tiling, resulting in issues with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, as well as can sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of drenched paper or soft rope. Remember to always load the tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealer can crack fairly very early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily offered on the marketplace. It is a good idea to fit the floor tiles using waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a fervent reader on Tools You Need to Install a New Bathtub , I figured sharing that piece of content was beneficial. Liked our post? Please share it. Help another person find it. I take joy in reading our article about How to Install a Bathtub.
Book My Estimate